Tel: 2997712; 2998696;
Under Construction
მულტიმედია და ბიზნეს კომპიუტერები
ხარისხი, გამოცდილება, პროფესიონალიზმი
Filter
ბრანდები
დალაგება: 
რაოდენობა: 
ხედვა: 

KVR16N11/8 8GB 2Rx8 1G x 64-Bit PC3-12800 CL11 240-Pin DIMM DESCRIPTION This document describes ValueRAM's 1G x 64-bit (8GB) DDR3-1600 CL11 SDRAM (Synchronous DRAM) 2Rx8, memory module, based on sixteen 512M x 8-bit FBGA components. The SPD is programmed to JEDEC standard latency DDR3-1600 timing of 11-11-11 at 1.5V. This 240-pin DIMM uses gold contact fingers. The electrical and mechanical specifications are as follows: FEATURES JEDEC standard 1.5V (1.425V ~1.575V) Power Supply VDDQ = 1.5V (1.425V ~ 1.575V) 800MHz fCK for 1600Mb/sec/pin 933MHz fCK for 1866Mb/sec/pin 8 independent internal banks Programmable CAS Latency: 11, 10, 9, 8, 7, 6 Programmable Additive Latency: 0, CL - 2, or CL - 1 clock 8-bit pre-fetch Burst Length: 8 (Interleave without any limit, sequential with starting address “000” only), 4 with tCCD = 4 which does not allow seamless read or write [either on the fly using A12 or MRS] Bi-directional Differential Data Strobe Internal (self) calibration : Internal self calibration through ZQ pin (RZQ : 240 ohm ± 1%) On Die Termination using ODT pin Average Refresh Period 7.8us at lower than TCASE 85°C, 3.9us at 85°C < TCASE < 95°C Asynchronous Reset PCB: Height 0.740” (18.75mm) or 1.180” (30.00mm) SPECIFICATIONS CL(IDDI) 11 cycles Row Cycle Time (tRCmin) 48.125ns(min.) Refresh to Active/Refresh Command Time (tRFCmin) 260ns (min.) Row Active Time (tRASmin) 35ns(min.) Maximum Operating Power TBD W* UL Rating 94 V - 0 Operating Temperature 0 oC to 85 oC Storage Temperature -55 oC to +100 oC *Power will vary depending on the SDRAM used.

Kingston ValueRAM 8 GB, DDR3, 240-pin DIMM, 1600 MHz, Memory voltage 1.5 V, ECC No, Registered No/Desktop
GEL 180
Limited: Call!
<475>

HX318C10FB/8 8GB 1G x 64-Bit DDR3-1866 CL10 240-Pin DIMM DESCRIPTION HyperX HX318C10FB/8 is a 1G x 64-bit (8GB) DDR3-1866 CL10 SDRAM (Synchronous DRAM) 2Rx8 memory module, based on sixteen 512M x 8-bit DDR3 FBGA components. This module has been tested to run at DDR3-1866 at a low latency timing of 10-11-10 at 1.5V. Additional timing parameters are shown in the PnP Timing Parameters section below. The JEDEC standard electrical and mechanical specifications are as follows: PnP JEDEC TIMING PARAMETERS: DDR3-1866 CL10-11-10 @1.5V FEATURES JEDEC standard 1.5V (1.425V ~1.575V) Power Supply VDDQ = 1.5V (1.425V ~ 1.575V) 933MHz fCK for 1866Mb/sec/pin 8 independent internal bank Programmable CAS Latency: 13, 11, 10, 9, 8, 7, 6 Programmable Additive Latency: 0, CL - 2, or CL - 1 clock 8-bit pre-fetch Burst Length: 8 (Interleave without any limit, sequential with starting address “000” only), 4 with tCCD = 4 which does not allow seamless read or write [either on the fly using A12 or MRS] Bi-directional Differential Data Strobe Internal (self) calibration : Internal self calibration through ZQ pin (RZQ : 240 ohm ± 1%) On Die Termination using ODT pin Average Refresh Period 7.8us at lower than TCASE 85°C, 3.9us at 85°C < TCASE < 95°C Asynchronous Reset Height 1.291” (32.80mm) w/heatsink, double sided SPECIFICATIONS CL(IDDI) 10 cycles Row Cycle Time (tRCmin) 44.75ns (min.) Refresh to Active/Refresh Command Time (tRFCmin) 260ns (min.) Row Active Time (tRASmin) 32.125ns (min.) Maximum Operating Power TBD W* UL Rating 94 V - 0 Operating Temperature 0 oC to 85 oC Storage Temperature -55 oC to +100 oC *Power will vary depending on the SDRAM used.

Kingston Fury Black 8 GB, DDR3, 240-pin DIMM, 1866 MHz, Memory voltage 1.5 V, ECC No, Registered No/Desktop
GEL 193
Limited: Call!
<407>

HX318C10FR/8 8GB 1G x 64-Bit DDR3-1866 CL10 240-Pin DIMM DESCRIPTION HyperX HX318C10FR/8 is a 1G x 64-bit (8GB) DDR3-1866 CL10 SDRAM (Synchronous DRAM) 2Rx8 memory module, based on sixteen 512M x 8-bit DDR3 FBGA components. This module has been tested to run at DDR3-1866 at a low latency timing of 10-11-10 at 1.5V. Additional timing parameters are shown in the PnP Timing Parameters section below. The JEDEC standard electrical and mechanical specifications are as follows: PnP JEDEC TIMING PARAMETERS: DDR3-1866 CL10-11-10 @1.5V FEATURES JEDEC standard 1.5V (1.425V ~1.575V) Power Supply VDDQ = 1.5V (1.425V ~ 1.575V) 933MHz fCK for 1866Mb/sec/pin 8 independent internal bank Programmable CAS Latency: 13, 11, 10, 9, 8, 7, 6 Programmable Additive Latency: 0, CL - 2, or CL - 1 clock 8-bit pre-fetch Burst Length: 8 (Interleave without any limit, sequential with starting address “000” only), 4 with tCCD = 4 which does not allow seamless read or write [either on the fly using A12 or MRS] Bi-directional Differential Data Strobe Internal(self) calibration : Internal self calibration through ZQ pin (RZQ : 240 ohm ± 1%) On Die Termination using ODT pin Average Refresh Period 7.8us at lower than TCASE 85°C, 3.9us at 85°C < TCASE < 95°C Asynchronous Reset Height 1.291” (32.80mm) w/heatsink, double sided SPECIFICATIONS CL(IDDI) 10 cycles Row Cycle Time (tRCmin) 44.75ns (min.) Refresh to Active/Refresh Command Time (tRFCmin) 260ns (min.) Row Active Time (tRASmin) 32.125ns (min.) Maximum Operating Power TBD W* UL Rating 94 V - 0 Operating Temperature 0 oC to 85 oC Storage Temperature -55 oC to +100 oC *Power will vary depending on the SDRAM used.

Kingston Fury Red 8 GB, DDR3, 240-pin DIMM, 1866 MHz, Memory voltage 1.5 V, ECC No, Registered No/Desktop
GEL 189
Limited: Call!
<407>

Kingston ValueRAM 4 GB, DDR3, 240-pin DIMM, 1600 MHz, Memory voltage 1.5 V MPN: KVR16N11S8/4 This document describes ValueRAM's 512M x 64-bit (4GB) DDR3-1600 CL11 SDRAM Synchronous DRAM) 1Rx8, memory module, based on eight 512M x 8-bit FBGA components. The SPD is programmed to JEDEC standard latency DDR3-1600 timing of 11-11-11 at 1.5V. This 240-pin DIMM uses gold contact fingers. The electrical and mechanical specifications are as follows: FEATURES JEDEC standard 1.5V (1.425V ~1.575V) Power Supply VDDQ = 1.5V (1.425V ~ 1.575V) 800MHz fCK for 1600Mb/sec/pin 8 independent internal bank Programmable CAS Latency: 11, 10, 9, 8, 7, 6 Programmable Additive Latency: 0, CL - 2, or CL - 1 clock 8-bit pre-fetch Burst Length: 8 (Interleave without any limit, sequential with starting address “000” only), 4 with tCCD = 4 which does not allow seamless read or write [either on the fly using A12 or MRS] Bi-directional Differential Data Strobe Internal(self) calibration : Internal self calibration through ZQ pin (RZQ : 240 ohm ± 1%) On Die Termination using ODT pin Average Refresh Period 7.8us at lower than TCASE 85°C, 3.9us at 85°C < TCASE < 95°C Asynchronous Reset PCB : Height 0.740” (18.75mm) or 1.180” (30.00mm) SPECIFICATIONS CL(IDD) 11 cycles Row Cycle Time (tRCmin) 48.125ns (min.) Refresh to Active/Refresh Command Time (tRFCmin) 260ns (min.) Row Active Time (tRASmin) 35ns (min.) Maximum Operating Power TBD W* UL Rating 94 V - 0 Operating Temperature 0o C to 85o C Storage Temperature -55o C to 100oC

Kingston DDR3 4GB 1600 KVR16N11S8/4G/Desktop
GEL 95
Limited: Call!
<358>

დალაგება: 
რაოდენობა: 
ხედვა: